ELISA Kit for Cubilin (CUBN)
IFCR; MGA1; gp280; Intrinsic Factor Cobalamin Receptor; 460 kDa receptor; Intestinal intrinsic factor receptor; Intrinsic factor-vitamin B12 receptor
- Product No.SEC411Ra
- Organism SpeciesRattus norvegicus (Rat) Same name, Different species.
- Sample TypeTissue homogenates, cell lysates and other biological fluids.
- Test MethodDouble-antibody Sandwich
- Assay Length3h
- Detection Range0.312-20ng/mL
- SensitivityThe minimum detectable dose of this kit is typically less than 0.114ng/mL.
- DownloadInstruction Manual
96T*5 96T*10 96T*100
Out of stock
For more details, please contact local distributors! US$ 760
For more details, please contact local distributors! US$ 3420
For more details, please contact local distributors! US$ 6460
For more details, please contact local distributors! US$ 53200
For more details, please contact local distributors!
This assay has high sensitivity and excellent specificity for detection of Cubilin (CUBN).
No significant cross-reactivity or interference between Cubilin (CUBN) and analogues was observed.
Matrices listed below were spiked with certain level of recombinant Cubilin (CUBN) and the recovery rates were calculated by comparing the measured value to the expected amount of Cubilin (CUBN) in samples.
|Matrix||Recovery range (%)||Average(%)|
Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Cubilin (CUBN) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Cubilin (CUBN) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Cubilin (CUBN) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.
The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.
Reagents and materials provided
|Pre-coated, ready to use 96-well strip plate||1||Plate sealer for 96 wells||4|
|Detection Reagent A||1×120µL||Assay Diluent A||1×12mL|
|Detection Reagent B||1×120µL||Assay Diluent B||1×12mL|
|TMB Substrate||1×9mL||Stop Solution||1×6mL|
|Wash Buffer (30 × concentrate)||1×20mL||Instruction manual||1|
Assay procedure summary
1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
8. Add 50µL Stop Solution. Read at 450nm immediately.
|Catalog No.||Related products for research use of Rattus norvegicus (Rat) Organism species||Applications (RESEARCH USE ONLY!)|
|RPC411Ra01||Recombinant Cubilin (CUBN)||Positive Control; Immunogen; SDS-PAGE; WB.|
|RPC411Ra02||Recombinant Cubilin (CUBN)||Positive Control; Immunogen; SDS-PAGE; WB.|
|RPC411Ra03||Recombinant Cubilin (CUBN)||Positive Control; Immunogen; SDS-PAGE; WB.|
|PAC411Ra01||Polyclonal Antibody to Cubilin (CUBN)||WB; IHC; ICC; IP.|
|PAC411Ra02||Polyclonal Antibody to Cubilin (CUBN)||WB; IHC; ICC; IP.|
|PAC411Ra03||Polyclonal Antibody to Cubilin (CUBN)||WB; IHC; ICC; IP.|
|LAC411Ra71||Biotin-Linked Polyclonal Antibody to Cubilin (CUBN)||WB; IHC; ICC.|
|SEC411Ra||ELISA Kit for Cubilin (CUBN)||Enzyme-linked immunosorbent assay for Antigen Detection.|